Products: print, build, walk.
Small-scale robots we design, 3D print and assemble ourselves. Each one starts as a desktop kit while we develop the full-size systems.
01 / The range
- POD-00In developmentWalker PodThe two-legged pod from our home page, as a desktop kit.
- HX-01In developmentHumanoidAn armoured humanoid with faceted panels and three-finger hands.
- WK-02In developmentHeavy WalkerA wide, heavy two-legged walker with shoulder pods and sensor clusters.
- SP-03In developmentCamera SpiderA four-legged walker that carries a camera on a pan-and-tilt hub.
#POD-00 Walker Pod
The two-legged pod from our home page, as a desktop kit.360° · drag to turn
A boxy sensor body on two reverse-knee legs with dampers and three-toe feet. The same robot that walks across the top of this site, scaled down for printing and assembly on a desk.
In the drawing: Walks in place, slows to a stop, crouches and looks around with its sensor head.
- Scale
- Desktop kitPlaceholder
- Build
- 3D-printed partsPlaceholder
- Moving joints
- 10Placeholder
- Height
- About 300 mmPlaceholder
- Control
- Microcontroller boardPlaceholder
- Price
- On launchPlaceholder
Views
Details
- P1
Sensor head
Pans and tilts on the neck, with the lens at the front.
- P2
Hip actuator
Drives each leg from the side of the body.
- P3
Knee and damper
Reverse knee with a spring damper to soften each step.
- P4
Three-toe foot
Hinged toes that lift and land with the stride.
#HX-01 Humanoid
An armoured humanoid with faceted panels and three-finger hands.360° · drag to turn
A walking humanoid with a faceted chest shell, an angular helmet with a visor slit, layered shoulder plates and plated legs over exposed joints. The panels are separate prints, so they can be swapped or painted.
In the drawing: Walks with its arms swinging against its legs, then stops, looks round and waves.
- Scale
- Desktop kitPlaceholder
- Build
- 3D-printed partsPlaceholder
- Moving joints
- 20Placeholder
- Height
- About 400 mmPlaceholder
- Control
- Microcontroller boardPlaceholder
- Price
- On launchPlaceholder
Views
Details
- P1
Helmet and visor
Angular helmet with a sensor eye behind the visor slit.
- P2
Chest shell
Faceted shield plate over the torso frame and waist joint.
- P3
Three-finger hand
Three fingers and a thumb that curl together to grip.
- P4
Knee and shin
Knee cap and shin shell with a calf piston behind.
- P5
Foot
Long sole with a toe plate and heel block for balance.
#WK-02 Heavy Walker
A wide, heavy two-legged walker with shoulder pods and sensor clusters.360° · drag to turn
A wedge-nosed body with two sensor clusters and twin antennas, a vented pod on each shoulder and big hip armour. Thick legs on round knee hubs, with knee pistons and feet that have two toes in front and a spur behind.
In the drawing: Takes slow, heavy steps that drop the body at each footfall, then turns and raises its pods.
- Scale
- Desktop kitPlaceholder
- Build
- 3D-printed partsPlaceholder
- Moving joints
- 9Placeholder
- Height
- About 350 mmPlaceholder
- Control
- Microcontroller boardPlaceholder
- Price
- On launchPlaceholder
Views
Details
- P1
Sensor cluster
Three lenses either side of the nose, one lit.
- P2
Shoulder pod
Vented pod that tilts up on a pivot at the shoulder.
- P3
Hip armour
Large plate over each hip actuator, marked with an X.
- P4
Knee hub
Round knee joint with a piston from thigh to shin.
- P5
Toed foot
Two front toes and a rear spur spread the load.
#SP-03 Camera Spider
A four-legged walker that carries a camera on a pan-and-tilt hub.360° · drag to turn
A rounded camera body with a zoom lens and a side viewfinder, on a geared pan-and-tilt hub. Four thin legs with a hip, femur and tibia each carry it over uneven ground, one leg at a time.
In the drawing: Creeps forward one leg at a time, then stops to sweep the camera and zoom the lens.
- Scale
- Desktop kitPlaceholder
- Build
- 3D-printed partsPlaceholder
- Moving joints
- 15Placeholder
- Height
- About 200 mmPlaceholder
- Control
- Microcontroller boardPlaceholder
- Price
- On launchPlaceholder
Views
Details
- P1
Zoom lens
Lens barrel that slides out to zoom while scanning.
- P2
Camera body
Rounded body with a viewfinder box and grip.
- P3
Pan-and-tilt hub
Geared turntable with a yoke for the camera tilt.
- P4
Leg
Hip yaw, femur and tibia; one lifts while three hold.